Radonix interface
3-Axis CNC Controller for Drilling Machines
Load a DXF, the software finds your holes, and the machine runs fast, accurate drill / peck / dwell cycles with guided manual tool changes and safe recovery.
- Axes
- 3-Axis
- Machine class
- Three-axis CNC drilling and hole-pattern machines
- Input
- DXF and standard G-code (e.g., ArtCAM / PowerMill posts)
- Controllers
- PC Smart 4APC Smart 3ASPC-Pro LAN 4A
01
Interface profile
Introduction
With CAM-Pro and compatible Radonix controller hardware, the XYZ CNC controller interface converts DXF hole geometry into controlled drilling, peck and dwell cycles.
- Who uses it
- Fabricators, HVAC & ducting, signage, general metalwork.
- Works with
- 3-axis gantry or table machines with a spindle/VFD (single tool, manual change).
- Compatible controllers
- PC Smart 4APC Smart 3ASPC-Pro LAN 4A
- Supported files
- DXF and standard G-code (e.g., ArtCAM / PowerMill posts)
02
Machine architecture
Machine & Kinematics
Machine & Kinematics
3-axis contouring (X, Y, Z) with homing and soft limits; work offsets (G54–G59).
Z executes drill/peck/dwell cycles with clean retracts to SafeZ.
Optional A-axis indexing (bolt circles on turned parts) if fitted.
Control & I/O
Spindle ON/OFF + RPM (VFD), coolant/mist/air, clamps/fixtures, beacons, guards, Emergency.
Inputs for home/limits, optional Z tool-setter, door/guard, vacuum/air-OK.
Operator aids: Feed/Speed overrides, Pause/Resume, Single-step, Restart from line (power-loss recovery).
03
Software workflow
Software & Workflow
- 01Home
X/Y/Z; set work offset (G54).
- 02Open DXF
→ holes are recognized and grouped by size.
- 03Drill/Peck/Dwell
Choose cycle (Drill/Peck/Dwell), set depths/steps, per-group feeds & RPM.
- 04Dry-run
(spindle off) to verify order, keep-outs, and SafeZ.
- 05Run
At tool change prompts: retract → stop spindle → change tool → (optional) probe Z → Resume.
- 06Restart from line
If interrupted, use Restart from line; then review and save the report.
04
Interface capabilities
Key Features of Radonix CNC Software
Software & Workflow
DXF-first: automatic hole recognition (circles/slots) → size groups → hit list.
Cycles: simple drill, peck drill (depth/step/clear), dwell (ms), counterbore/countersink depths.
Pattern tools: array, grid, bolt circle, along polyline; per-group feeds/RPM.
Clamp-aware planning with keep-out zones, inner→outer order, safe pauses for reposition.
3D preview of Z moves; Floor (max depth) to protect table/fixtures.
Job reports: hole count, travel distance, cycle time, pauses/alarms, operator notes.
Key Capabilities (at a glance)
DXF import with auto hole detection & sizing
Drill / Peck / Dwell cycles with SafeZ retracts
Per-group feeds/RPM, pattern generators (grid/array/bolt circle)
Clamp keep-outs, inner→outer sequencing, dry-run (spindle off)
Z tool-setter support for accurate depths (optional)
Restart from last G-code line after stop or power cut
Floor depth limit, soft limits, full safety interlocks
Three-axis drilling cycles:
Coordinate X, Y and Z for drilling, peck and dwell cycles with configured SafeZ retracts.
Automatic DXF hole detection:
Detect supported hole geometry and convert it into verified drilling positions and cycles.
Pattern generation
Create repeatable grid, array and bolt-circle drilling patterns with controlled spacing.
SafeZ and keep-out control:
Use SafeZ retracts, clamp keep-outs and inner-to-outer sequencing for collision-aware drilling.
Automatic Z tool offset & referencing:
Use the optional Z tool setter and configured depth limits for repeatable hole depth.
3D toolpath & rotary visualization:
Preview the three-axis drilling path, run with the spindle off and resume safely after a stop.
Floor (depth) limit:
Enforces a maximum Z penetration so the tool never cuts past the programmed floor—protects the table, fixtures, and laminated stacks.
05
Technical reference
Typical Specifications
| Area | Spec |
| Axes / Modes | XYZ |
| File Formats | DXF, standard G-code |
| Compensation | Kerf/offset, corner smoothing, arc tolerance |
| Performance | High look-ahead planner; steady velocity on arcs |
| I/O | Spindle, Safety relays , Solenoid Valve , Jacks |
| Work Offsets | Multiple origins for sheet/remainder reuse |
| Reports | Time, cut length, pierces, alarms, notes |
06
Operating evidence
Videos & Demos
Real-world clips of Radonix interfaces on production machines—setup, operation, quality tips, and quick troubleshooting.
07
Compatible hardware