Radonix interface
3-Axis Waterjet CNC Controller for Precision Cutting
Import a DXF, set pierce timing, choose Low/High Pressure and Abrasive mode, and cut accurately while Z maintains safe standoff and the interface sequences pump, valves, and feeds automatically.
- Axes
- 3-Axis
- Machine class
- Three-axis CNC waterjet cutting machines
- Input
- DXF and standard G-code (e.g., ArtCAM / PowerMill posts)
- Controllers
- PC Smart 4APC Smart 3ASPC-Pro LAN 4A
01
Interface profile
Introduction
With CAM-Pro and compatible Radonix controller hardware, the XYZ CNC controller interface coordinates three-axis waterjet motion, pump sequencing, abrasive control and safe standoff.
- Who uses it
- Metal & composite job shops · gasket makers · stone/glass processors · prototyping & education.
- Works with
- 3-axis gantry waterjets with an HP pump (intensifier or direct-drive), abrasive feeder, and Z lifter.
- Compatible controllers
- PC Smart 4APC Smart 3ASPC-Pro LAN 4A
- Supported files
- DXF and standard G-code (e.g., ArtCAM / PowerMill posts)
02
Machine architecture
Machine & Kinematics
Machine & Kinematics
3-axis contouring (X, Y, Z) with homing and soft limits; work offsets
Two programmable positions (P1 / P2) for quick park, tool change, or fixture points.
Sheet Align to rotate/shift the program to the clamped sheet with one reference move.
Control & I/O
- Pump and cutting-head control: HP / LP water, abrasive ON/OFF, purge/bleed, nozzle enable, guards and emergency chain.
Inputs: home/limits, pump ready, pressure OK, door/guard, optional height/touch sensor.
Operator aids: Speed % override, Pause/Resume, Jog (continuous or incremental), Restart from line (power-loss recovery).
03
Software workflow
Software & Workflow
- 01Home
X/Y/Z → set X0/Y0/Z0 and verify SafeZ.
- 02Open DXF
→ set kerf, leads, tabs, and corner slow-down.
- 03Pre-Cut / Cut / Post-Cut
Configure Pre-Cut / Cut / Post-Cut times; choose LP/HP and Abrasive.
- 04Dry-run
(water off) to check order and clearances → adjust Speed % if needed.
- 05Run
system sequences pump/valves automatically; pause safely for inspection or reposition.
- 06Restart from line
If interrupted, use Restart from line, confirm SafeZ and re-entry, and resume.
- 07save the run report.
Inspect parts and save the run report.
04
Interface capabilities
Key Features of Radonix CNC Software
Software & Workflow
DXF import with preview, kerf/offset, lead-in/lead-out, tabs, inner→outer ordering, and corner slow-down.
Pierce strategies: LP (water-only) pierce → ramp to HP + Abrasive; configurable Pre-Cut (pre-flow), Cut timing base, and Post-Cut (post-flow).
Dry-run (water off) to validate order, clearances, and keep-outs, then Run with live overrides.
Automatic job report (time, path length, pierces, pauses/alarms, operator notes).
Key Capabilities (at a glance)
Direct DXF execution (no external post needed)
Low/High-pressure modes and Abrasive control from the HMI
Programmable pierce timing (pre-flow / dwell / post-flow)
Kerf compensation, clean leads, micro-tabs, and corner smoothing
Sheet Align rotation/shift to the clamped sheet
SafeZ retracts, feed overrides, Pause/Resume, and Restart from line
Direct DXF Execution
Seamlessly load and execute DXF files without the need for G-code conversion — streamlining your workflow and reducing setup time.
Smart Component & Path Management
Select specific parts from complex drawings and customize cutting order with intuitive control over toolpath sequencing.
Interactive On-Screen Editing
Scale, rotate, and mirror parts directly within the interface — with live toolpath previews to ensure precision.
Flexible Part Placement
Manually drag and drop parts onto your material sheet to accommodate irregular shapes, pre-cut stock, or remnant reuse.
Advanced Pause Controls
Set up to three independent pause points — before the cut, during the cut, and after the cut — for manual checks or operational adjustments.
Reverse Cutting Mode
Execute toolpaths in reverse to minimize material warping or adjust final exit points based on design needs.
Simulation / Demo Run Mode
Perform a complete dry-run motion test with the pump and abrasive disabled to verify the waterjet path and clearances.
Cylindrical Cutting Capability
Project flat designs onto cylindrical surfaces for precision tube and pipe cutting operations.
Abrasive feeder control:
Enable/disable abrasive and, where supported, set the feed rate from the HMI.🔹Automatic standoff control:Z lifter/height sensor keeps a constant nozzle-to-work gap for consistent kerf and quality.
Automatic standoff control:
Z lifter/height sensor keeps a constant nozzle-to-work gap for consistent kerf and quality.
05
Technical reference
Typical Specifications
| Area | Spec |
|---|---|
| Axes | X,Y,Z |
| Modes | DXF revolve to 3D, multi-pass rough/finish, RPM control |
| Files | DXF (primary), G-code (optional) |
| Piercing | Waterjet: pierce timing, pressure mode, abrasive control and cutting direction. |
| Compensation | Junction smoothing, velocity planning, SafeZ retracts |
| Alignment | P1/P2 quick points, origin tools, 3D preview verification |
| Safety | Guard/door, spindle ready, tailstock clamp, E-stop, SafeZ |
| Recovery | Restart from last line; safe RPM and clearance restore |
| Reporting | Time, path length, passes, pauses/alarms, notes |
06
Operating evidence
Videos & Demos
Real-world clips of Radonix interfaces on production machines—setup, operation, quality tips, and quick troubleshooting.
07
Compatible hardware